![]() Shift is a temporary button that allow a secondary function on another control. Tip: use the Aux input to connect a smartphone as a backup device, the AUX input is Hardware driven and can work without DJUCED.Īpplies a High/Low pass Filter to the AUX input. When far to the left, the Auxiliary Input is totally muted. Note: the Microphone input is Hardware driven and can work without DJUCED.Īdjusts the High frequencies of the Microphone Input signalĪdjusts the Low frequencies of the Microphone Input signalĪdjusts the level of the Auxiliary Input (connection at the rear panel on dual RCA or mini jack). When far to the left, the Microphone Input is totally muted. Use the Vu-Meter ring to set up properly the level of the sound. This is why you can’t change DJUCED headphone’s volume on the user interface.Īdjusts the level of the Microphone Input (connection at the rear panel). Note: The Headphones Volume is Hardware driven and is not reflecting the software Headphones volume. (to the connected headphones on the front of the controller). This is why you can’t change DJUCED master volume on the user interface.īlends the signal from the Deck (CUE Channel) and the Master Output in Headphones.Ĭontrols the amount of volume sent to the Headphones. Note: The Master Volume is Hardware driven and is not reflecting the software Master volume. (to the connected speakers on the back of the controller). ![]() Simple press = Load the selected song in the Browser list or Assistant into the Left/Right Deck.Ĭontrols the amount of volume sent to the Master. Press + Turn the encoder to change the Energy level of the Assistant suggestion, and use the Color ring to choose between 6 Levels of energy (Blue = Low Energy, Red = High Energy). Navigate through your audio library when turning the encoder, or change levels/open folders by pressing the encoder. Opens/Close the Intelligent Music Assistant panel on DJUCED Browser. Note: These Vu-Meters are Hardware driven and are not reflecting the software Master Vu-meters. Indicate the audio output level sent to the Master. Tip: Always try to stay between the maximum green/orange area to avoid clipping in the red. Indicate the pre-faders level of the Left/Right Decks. In all other positions, the audio signals from left/right decks will be a blend.Įnable/Disable the Beatmatch Guide LEDs that you will find on the Decks. When at the far right position, only the sound of the right deck will be heard from the Master Output. When at the far left position, only the sound from the left deck will be heard from the Master Output. (like your Internet browser, Music software, video game…)Īdjust the volume of the Left/Right deck. Tip: the Master Headphones button allows you to listen to any source that is sent to the 1-2 Channel Audio Output of the Inpulse sound card – if you use the Inpulse as a computer sound card. You can also use the Master headphones button to preview the Master signal that you are sending to the speakers. The buttons with a headphones symbol on them send the pre-fader audio signal of the Left/Right deck to the Headphones channel (also called the CUE audio channel) for pre-listening (connection at the front side). ![]() Go to DJUCED Settings => Mixer to personalize your Filter FX. If FX1, 2, 3, or 4 is activated, the Filter Knob applies a Filter FXĪpplies effects FX1 to FX4 (modulated via the Filter knob) on decks 1 and 2. Use this knob to apply a low-pass filter (left) or high-pass filter (right), enabled when FX1, 2, 3, and 4 are off. Tip: remove Bass instead of boosting them when making a transition. Use this knob to cut/boost the frequencies of the Low (Bass) Equaliser Band. Use this knob to cut/boost the frequencies of the Mid (Middle) Equaliser Band. Use this knob to cut/boost the frequencies of the High (Treble) Equaliser Band.Īt the middle/center position, the EQ is OFF. Tip: Adjust your gain level with the help of the Vu-Meter, the overall level should be around 0 dB. When the knob is at the middle/center position, the track will be at its original level. Use this knob to adjust the pre-fader output level of the Left/Right deck.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |